Recent Posts

Pages: [1] 2 3 4 5 6 ... 10
1
Embedded development / Re: error: -mmcu
« Last post by Miguel Gimenez on Yesterday at 11:49:47 am »
Follow the link I gave you in reply #3 and post a full rebuild log (use code tags, please).
2
Embedded development / Re: error: -mmcu
« Last post by Nayani on Yesterday at 11:41:07 am »
HI Miguel Gimenez,
I tried command line and the build (only compile) seems to have gone through without a hitch. Here is what I typed

msp430-elf-gcc -c -IC:\ti\msp430-gcc\include -mmcu=msp430f67791 main.c   

The main.c file content, copied from the NET

#include "msp430f67791.h"
//#include <msp430.h>            

int main(void) {
   WDTCTL = WDTPW | WDTHOLD;      // Stop watchdog timer
   P1DIR |= 0x01;               // Set P1.0 to output direction

   for(;;) {
      volatile unsigned int i;   // volatile to prevent optimization

      P1OUT ^= 0x01;            // Toggle P1.0 using exclusive-OR

      i = 10000;               // SW Delay
      do i--;
      while(i != 0);
   }
   
   return 0;
}

The issue is to configure code::blocks properly!!!! Not getting it.

3
Profile spammer reported to moderator.
4
Currently I have not seen any notification yet. Looking forward!
5
Nightly builds / Re: The 28 January 2024 build (13434) is out.
« Last post by SharkCZ on June 12, 2024, 10:52:48 pm »
I have just pushed the latest nightly as an update to Fedora 40 (see https://bodhi.fedoraproject.org/updates/FEDORA-2024-106b2196b0). Most of the nightly builds is available from https://copr.fedorainfracloud.org/coprs/sharkcz/danny/ after they are announced.
6
Embedded development / Re: error: -mmcu
« Last post by Nayani on June 12, 2024, 01:19:34 pm »
Thank you. I did tick (selected the controller from the available list) however the compiler complains about "mmcu" not being set. This is the issue. I will try the command line and update you.

RGDS
NPS
7
Embedded development / Re: error: -mmcu
« Last post by Miguel Gimenez on June 12, 2024, 01:03:05 pm »
Using the specific compiler is the way relevant options are supported, so you do not need to add other compiler options.
Ticking the MCU will generate the "-mmcu=" flag, enable full build log and check.
8
Embedded development / Re: error: -mmcu
« Last post by Nayani on June 12, 2024, 12:41:33 pm »
Hi Miguel Gimenez,
Thank you very much for your reply. Just wanted to clarify
1. Is it necessary to use "GNU GCC Compiler for MSP430 (HighTec)" compiler only? As mentioned earlier I have msp430-gcc compiler and I included a sample header file, which gave no errors. MSP430GCC has support for my controller.
2. In case the CPU is listed, by selecting (ticking), "-mmcu=" flag should have been generated/added. Am I right? Or is it necessary that I add this under "other compiler options"?

I await your reply. Thanks once again.
Regards
NPS
9
General (but related to Code::Blocks) / Re: antivirs bitdefender
« Last post by Miguel Gimenez on June 12, 2024, 11:11:15 am »
Profile spammer reported to moderator.
10
Embedded development / Re: error: -mmcu
« Last post by Miguel Gimenez on June 12, 2024, 11:10:22 am »
You should use the "GNU GCC Compiler for MSP430 (HighTec)". If your CPU is not listed, but suported by the compiler, you can add it in the "Other compiler options", p.e. -mmcu=mps430xG666
Pages: [1] 2 3 4 5 6 ... 10